14 July 2011 - Kyoto/Neuss – Kyocera Corporation today announced that it has developed the KVL-G3 Series LED-UV curing system, a key component in industrial printing machines, which supports the industry’s fastest label printing (80m/min.)*¹ for use in UV curing-type printing — a printing method that hardens and fixes ink with irradiating ultraviolet (UV) rays. Moreover, the new product achieves a 70% reduction*² in power consumption by using light-emitting diodes (LEDs) in place of conventional lamp-system products (metal halide*³). The KVL-G3 Series was made available to the market on July 8.
Recently, the use of digital printing, which enables fast printing of even small-volume wide-variety labels in a short delivery time, is expanding in the label printing market mainly engaged in printing product packages for commodities such as beverages. Among the various printing methods, the UV curing-type attracts attention due to its convenience in allowing printing on a wide variety of non-paper media including plastic sheets, as it enables printing without the need for ink to penetrate the print medium, as well as its eco-friendly composition that does not use volatile organic compounds (VOCs) as solvents.
The KVL-G3 Series features a power-saving system which enables a 70% reduction in electricity consumption compared to existing lamp-system products (metal halide) by using LEDs as the light source for curing ink. In addition, thanks to Kyocera’s proprietary high-density packaging technologies, the company has succeeded in arranging LED chips on a high-density surface as opposed to in-line conventional products. With this development, Kyocera has enabled the fastest label printing capability for the UV curing-type printing method in the industry (80m/min).
Kyocera has been actively rolling out inkjet printheads, key devices for digital printing, which feature high-speed, high-definition and highly reliable printing. With the launch of this product, the company proposes an even more efficient printing method by combining its inkjet printhead and LED-UV curing system. In addition, in other markets such as offset printing, Kyocera will actively encourage customers to replace their current UV curing systems — which use much higher energy-consuming lamps — with this new product by focusing on its superior energy-saving features. In doing so, Kyocera aims to contribute to reducing the environmental burden within the printing industry.
Kyocera will exhibit this product at the Auto ID Expo 2011, which will be held from August 31 to September 2, 2011, at the Tokyo Big Sight international convention center.
1. Consistent curing performance that enables high-speed printing
An industry first, Kyocera mounted LED chips in high density on a heat releasing ceramic substrate utilizing the company’s core technology, and has thus developed a surface area-emitting LED-type UV light with high illuminance and integral light. This light enables consistent curing performance even during high-speed printing.
2. Improved illuminance via micro lens array
Installation of a micro lens array (small lenses arranged in bundles), which is optimized for surface emission of UV-LEDs, improves illuminance and reduces degradation of illuminance over increasing distance.
3. Substantial energy and space saving via use of LEDs
The use of LEDs as a UV light source achieves a 70% reduction in power consumption under full-lighting conditions compared to existing lamp-system products (metal halide), as well as a substantial cost reduction because the cost and manpower for replacing lamps becomes obsolete. At the same time, substantially simplified auxiliary facilities for evacuation of air and cooling enable space saving in the overall installation of equipment.
4. Extended product life via integrated water-cooling heat-sink structure
By using an integral structure for the substrate and water-cooling heat sink (which reduces temperature in the equipment by dissipating heat), the LED module may be cooled down efficiently while illuminance is maintained at the same time. The result is enhanced product life due to minimal temperature increases.
5. Enhanced energy savings via Kyocera’s proprietary controls
Kyocera’s proprietary LED emitting controller enables adjustment of the LED source, light control and light-emitting width. This light-emitting width adjustment function makes it possible to turn off unused LEDs according to the print media width. In addition, an external remote function enables the light to be turned on or off in conjunction with the printer’s operation, achieving energy savings by taking advantage of the characteristics of LEDs.
|Series||KVL-G3 Series LED-UV Curing System|
|Size of irradiator
(Width x Depth x Height)
|252 × 83 × 170 (mm)||360 × 83 × 170 (mm)|
|LED wave length||385 nm|
|Irradiation area||110 × 48 (mm)||220 × 48 (mm)||220 × 24 (mm)|
|Designated life||15.000 hours|
|Weight||2,5 kg||2,8 kg|
(200 - 240 V AC)
(200 - 240 V AC)
(200 - 240 V AC)
|Production Plant||Shiga Yohkaichi Plant (Shiga Prefecture, Japan)|
|Sales target||Starting from 300 million yen for FY2012 and aiming at 5 billion yen for FY2016|
*¹ Based on research by Kyocera. This speed is confirmed in inkjet type
label printing (as of July 7, 2011).
*² Based on research by Kyocera. Estimated using the KVL-S09E-G3 when compared to a metal halide lamp of 4.8kW, and based on the following conditions: 8 hours/day x 250 days of operation/year
*³ A lamp utilizing light emission with electric discharge of mercury and halogenated metal (metal halide).
For more information about Kyocera Printing Devices: